eraflash

The all-round flash point tester.

The flash point tester eraflash measures in full compliance with the Continuously Closed Cup flash point testing methods ASTM D6450, ASTM D7094 as well as the European equivalent IP620. ASTM D7094 shows no statistical bias to the former ASTM D93 Pensky Martens method. The sample volume is only 2 ml. During measurements an electric arc ignites the sample vapor and the analyzer determines the flash point by the pressure change inside the closed cup. Flash point testing never was safer and easier.

360° View

Standards

Correlations

ASTM D7094 and ASTM D6450

ASTM D6450 was the first Continuously Closed Cup Flash Point (CCCFP) and uses 1 ml sample volume only. To further improve the correlation to the well-established ASTM D93 Pensky Martens method a modified successor method was developed.

ASTM D7094 (Modified CCCFP) uses 2 ml of sample volume and a different heating rate than ASTM D6450 with the effect that it shows no statistical bias to ASTM D93 (Pensky Martens). This was proven by an ASTM round robin test in 2004.

In addition this round robin showed, that the actual repeatability and reproducibility of ASTM D7094 is up to 50% better than the values stated in ASTM D93.

Fuel specifications testing

In December 2013 ASTM D7094 was accepted as the first official alternative for fuel specification testing as it gives equivalent results to ASTM D93 and even outperforms it in terms of reproducibility:

Fuel oil (ASTM D396)
Diesel fuel (ASTM D975)
Gas turbine fuel oil (ASTM D2880)
Kerosene (ASTM D3699)
Diesel Fuel, Biodiesel Blend (ASTM D7467)

Unmatched range meets high performance

eralytics’ patented PBT – Peltier Boost Technology® allows flash point testing below 0 °C (32 °F) and above 200 °C (392 °F) with a single instrument. This technology separates the Peltier elements during the heat up from the oven to prevent any damage to them at high temperatures. Additionally the Peltier elements can be used during cool down at temperatures that would normally harm them. Thus, the turnaround time is significantly shortened. On top PBT makes eraflash the only flash point tester on the market covering a temperature range of -25 °C (-13 °F) to 420 °C (788 °F).

High sample throughput with minimum maintenance

The innovative PBT – Peltier Boost Technology® allows previously unmatched heating and cooling rates, which in combination with the low sample volume decreased the turnaround time significantly for flash point testing. Additionally the CPT – Contamination Prevention Technology™, which is a combination of advanced electrode protection and self-cleaning procedures, reduces the time required for cleaning and maintenance to an absolute minimum, increasing the sample throughput even further.

eraflash & Density

With the temperature-controlled x-oscillating metal U-tube technology inside, eradens xs measures density with 5-digit precision. eradens xs is also available for the direct connection with eraflash. The measured density result is available within seconds on your analyzer. Depending on your needs eradens xs provides the perfect solution across most industries, from the petroleum industry to the food, beverage, or the flavors and fragrance industry.

Measurement procedure

Just four easy steps are required for a safe flash point testing at maximum precision:

Enter sample ID and operator name
Select the measurement standard and add additional parameters (e.g. expected flash point)
Fill the sample cup with sample, place the sample cup inside the measurement chamber, and close the door
Press the RUN button

The instrument now visualizes the measurement procedure on the screen showing the sample and oven temperature as well as pressure gauge displaying the pressure increase after ignition. After the measurement the flash point temperature is corrected for the atmospheric pressure and rounded to the next 0.5 °C. The result will be saved in the corresponding result file.

Characteristics of the flash point testing can be seen in the Combustion Graphics™. This makes eraflash the ideal solution for R&D as well as quality control.

eraflash feature video

Inherently safe with no open flame
Only a very low sample volume of 1-2 mL needed
Fully compliant with ASTM D6450, ASTM D7094, IP620
Measurement of fuels, lubricants, fragrances, flavors, paints, …

You are currently viewing a placeholder content from YouTube. To access the actual content, click the button below. Please note that doing so will share data with third-party providers.

More Information

eraflash operation video

Watch this video to get an overview on the standard operation of eraflash: From installation to measurement and some extended measuring options.