arrow-left feather Flag of the People's Republic of China flag-deFlag of Germany flag-es flag-jp flag-rumail marker media-archive media-default media-document phone rotate-right search social-googleplus social-linkedin social-youtube
Contact

ERAFLASH

The Safe Side of Flash Point Testing

The flash point tester ERAFLASH measures in full compliance with the Continuously Closed Cup flash point testing methods ASTM D6450, ASTM D7094 as well as the European equivalent IP620. ASTM D7094 shows no statistical bias to the former ASTM D93 Pensky Martens method. The sample volume is only 2 ml. During measurements an electric arc ignites the sample vapor and the analyzer determines the flash point by the pressure change inside the closed cup. Flash point testing never was safer and easier.

Standards

Correlation to

  • ASTM D56
    • ASTM D93
  • ASTM D3828
  • DIN 51758
  • ISO 2719
  • ISO 3679
  • ISO 3680
  • ISO 13736
  • IP34
  • IP170
  • JIS K2265

360° View

ASTM D7094 and ASTM D6450

ASTM D6450 was the first Continuously Closed Cup Flash Point (CCCFP) and uses 1 ml sample volume only. To further improve the correlation to the well-established ASTM D93 Pensky Martens method a modified successor method was developed.

ASTM D7094 (Modified CCCFP) uses 2 ml of sample volume and a different heating rate than ASTM D6450 with the effect that it shows no statistical bias to ASTM D93 (Pensky Martens). This was proven by an ASTM round robin test in 2004.

In addition this round robin showed, that the actual repeatability and reproducibility of ASTM D7094 is up to 50% better than the values stated in ASTM D93.

Comparison Flash Point Tester Standards

Fuel Specifications Testing

In December 2013 ASTM D7094 was accepted as the first official alternative for fuel specification testing as it gives equivalent results to ASTM D93 and even outperforms it in terms of reproducibility:

  • Fuel oil (ASTM D396)
  • Diesel fuel (ASTM D975)
  • Gas turbine fuel oil (ASTM D2880)
  • Kerosene (ASTM D3699)
  • Diesel Fuel, Biodiesel Blend (ASTM D7467)
4 gas pump nozzles at a gas station

Unmatched Range Meets High Performance

eralytics’ patented PBT – Peltier Boost Technology® allows flash point testing below 0 °C (32 °F) and above 200 °C (392 °F) with a single instrument. This technology separates the Peltier elements during the heat up from the oven to prevent any damage to them at high temperatures. Additionally the Peltier elements can be used during cool down at temperatures that would normally harm them. Thus, the turnaround time is significantly shortened. On top PBT makes ERAFLASH the only flash point tester on the market covering a temperature range of -25 °C (-13 °F) to 420 °C (788 °F).

  • Flash Point Measurment Screen
  • Flash point result 8XXX

High Sample Throughput with Minimum Maintenance

The innovative PBT – Peltier Boost Technology® allows previously unmatched heating and cooling rates, which in combination with the low sample volume decreased the turnaround time significantly for flash point testing. Additionally the CPT – Contamination Prevention Technology™, which is a combination of  advanced electrode protection and self-cleaning procedures, reduces the time required for cleaning and maintenance to an absolute minimum, increasing the sample throughput even further.

10 ASTM D7094 sample cups

ERAFLASH & Density

With the temperature-controlled x-oscillating metal U-tube technology inside, ERADENS XS measures density with 5-digit precision. ERADENS XS is also available for the direct connection with ERAFLASH. The measured density result is available within seconds on your analyzer. Depending on your needs ERADENS XS provides the perfect solution across most industries, from the petroleum industry to the food, beverage, or the flavors and fragrance industry.

ERAFLASH measuring density

Measurement Procedure

Just four easy steps are required for a safe flash point testing at maximum precision:

  • Enter sample ID and operator name
  • Select the measurement standard and add additional parameters (e.g. expected flash point)
  • Fill the sample cup with sample, place the sample cup inside the measurement chamber, and close the door
  • Press the RUN button

The instrument now visualizes the measurement procedure on the screen showing the sample and oven temperature as well as pressure gauge displaying the pressure increase after ignition. After the measurement the flash point temperature is corrected for the atmospheric pressure and rounded to the next 0.5 °C. The result will be saved in the corresponding result file.

Characteristics of the flash point testing can be seen in the Combustion Graphics™. This makes ERAFLASH the ideal solution for R&D as well as quality control.

  • Measure Screen of ERAFLASH
  • Flash Point measurement screen
  • Flash Point result screen

ERAFLASH Feature Video

  • Inherently safe with no open flame
  • Only a very low sample volume of 1-2 mL needed
  • Fully compliant with ASTM D6450, ASTM D7094,  IP620
  • Measurement of fuels, lubricants, fragrances, flavors, paints, …
YouTube

By loading the video, you agree to YouTube's privacy policy.
Learn more

Load video

ERAFLASH Operation Video

Watch this video to get an overview on the standard operation of ERAFLASH: From installation to measurement and some extended measuring options.

YouTube

By loading the video, you agree to YouTube's privacy policy.
Learn more

Load video

Technical Specifications

Available Test Methods
ASTM D6450, ASTM D7094, IP620, SH/T 0768,
US D.O.T / RCRA / NAVY and NATO reference methods
Pre-Programmed Correlation Methods to...
Pensky Martens Closed Cup: ASTM D93, EN ISO 2719, DIN 51758, IP34, JIS K2265
TAG Closed Cup: ASTM D56
Abel Pensky Closed Cup: ISO 13736, IP170
Small Scale Closed Cup and Flash / No Flash methods: EN ISO 3679, EN ISO 3680, ASTM D3828
Fuel Specifications (ASTM D7094)
ASTM D396, ASTM D975, ASTM D2880, ASTM D3699, ASTM D7467
Speed Tests
Fast screening test programs for unknown samples
PBT - Peltier Boost Technology®
High speed heating & cooling
-25 °C to 420 °C (-13 °F to 788 °F) with a single analyzer
CPT - Contamination Prevention Technology™
Advanced electrode protection and self-cleaning ignition system to minimize cleaning and maintenance
Combustion Graphics™
Display of combustion characteristics for contamination analysis
QuickCal™
In-situ calibration with eralytics unique calibration cups without the need of dismantling the instrument
Fuel Dilution Program
Automatic fuel dilution measurement for the analysis of used engine oils

Downloads

Please contact us. By filling out the form below, we will get in touch with you as soon as possible.

By sending this contact form I agree, that eralytics GmbH, Autokaderstrasse 29, Building 4A, 1210 Wien, office@eralytics.com will save my personal data to process my request or use my data for occasional marketing activities. Further information can be found in the Privacy Policy.